Beko Washing Machine Not Draining – Issue Solved

Beko is one of the most reliable name brand appliance manufacturers in the world. However, like other well-known companies, they have their share of problems too. One of those problems is the Beko washing machine not draining. 

The drain pump in the bottom of the drum gets clogged up with lint and other debris from the wash cycle. This causes the water level to drop in the drum and prevents the water from draining out.

This problem can be quite annoying for customers who are on the other end of the line while a repair person is trying to figure out what’s wrong with their appliance.

Beko Washing Machine Not Draining

Beko Washing Machine Not Draining

To help you quickly diagnose this problem and easily solve it, we have compiled a list of the most common issues for Beko Washing Machine Not Draining.

1. Check the Drain Pump Filter:

Beko washing machines use a filter to keep the water flowing in a continuous stream. This filter can get clogged up very easily, especially when there is lint buildup in the drain pipe.

Check the filter and make sure that it has not gotten clogged up with lint or debris. 

Usually, the drain pump is located at the bottom of the drum and is triggered by the spin cycle. This drain pump has a small hose that goes all the way around the inside of the drum and discharges water from the bottom of the drum.

This water then drains out through a pipe attached to the bottom of the drum.

However, during the wash cycle, the drum is not spinning and the water does not drain out. This leaves a lot of lint and other debris in the bottom of the drum.

2. Check the Drain Pump Timer:

If the drain pump was on the spin cycle timer, it will be set to turn on after 5 minutes and shut off after 10 minutes.

However, if you find that the drain pump is not functioning for any reason, you should check the timer. If the timer has expired, the drain pump will not work and you should contact your Beko repair center for assistance.

3. Inspect the Water Level Control Knob:

The water level control knob adjusts the water level in the drum. It should be set all the way down (least amount) so that all of the water can be drained out.

The water level control knob is located on the outside of the drum and is used to adjust the water level in the drum.

If the water level is too high, it could prevent the water from draining out. Make sure the water level control knob is in the “empty” position. When you turn the knob counterclockwise, water will come out of the hose.

4. Clean the Draining Hose:

The hose going from the bottom of the drum to the drain pump is called the “draining hose.” During the wash cycle, this hose gets very dirty and clogged up with lint and other debris. This makes it difficult for the water to drain and causes the Beko washing machine not to drain properly.

To clean this hose, remove the washer from the wall mount and detach the drain pipe from the bottom of the drum. Turn the water hose that comes out of the bottom of the drum upside down and use a brush or wire brush to remove as much of the debris as you can.

When cleaning this hose, avoid using any strong chemicals.

5. Clean the Inside of the Drum: 

The inside of the drum has a mesh basket that holds the laundry. This basket gets very dirty and full of lint and other debris during the wash cycle.

This debris prevents the clothes from getting cleaned and can also cause the drum to rust and stop draining.

So, here are a few simple tips to clean the inside of the drum:

  • Get a bucket of warm water and some dish soap.
  • Mix one part water to two parts soap in a bucket.
  • Fill the drum with water up to the maximum fill line.
  • Let the washing machine run with the spin cycle for 10 minutes.
  • Then, remove the plug from the drain hose and allow the water and soap to flow out of the drum.
  • Use a brush or a wire brush to scrub the inside of the drum.

Make sure you get into all of the hard-to-reach areas. Washing machines have a lot of crevices and little nooks and crannies that can become clogged with lint and other debris.

However, if the machine is not agitating, you can read our complete guide on the Beko Washing Machine Not Spinning issue.

6. Replace the Drain Pump: 

The drain pump is the most important part of your Beko washing machine. It allows the washing machine to drain properly and remove any remaining water and lint from the inside of the drum.

If the drain pump malfunctions, it could cause serious problems. It could prevent the water from draining out of the bottom of the drum, which would cause the water to fill up and overflow. This might also prevent the spin cycle from draining the washing machine.

You need to replace the drain pump if it has failed at any time. If you find a leak in the drain pipe, you may be able to repair this yourself. But, if you plan to buy a new washer, then here are the washing machine brands to avoid.

7. Check the Drive Belt:

If the drive belt is slipping, then the motor will not be able to turn the drum fast enough to achieve proper agitation and drainage.

This will cause a lot of lint to build up in the bottom of the drum and prevent the water from draining out. Replace the belt if it is worn or broken.

Conclusion:

So, there you have it – 7 simple steps to fix your Beko washing machine not draining problem. Make sure that you follow these steps regularly to help prevent the drain pump from malfunctioning and causing serious damage to your machine.

Beko Washing Machines are some of the most reliable machines available. If you keep up with the recommended maintenance, then these machines will last a very long time. There is really nothing more to it than a quick and easy cleaning.

Be sure to check your manual for any additional instructions before doing any maintenance work.

Leave a Comment